Hi the guy that usually does my alloy polishing is spending some time away at her Majesty's pleasure so any suggestions on who I use.
Cheers Ian.
Hello Guest User,
Please feel free to have a look around the forum but be aware that as an unregistered guest you can't see all of it and you can't post.
To access these 'Registered Users Only' areas simply register and login.
Please feel free to have a look around the forum but be aware that as an unregistered guest you can't see all of it and you can't post.
To access these 'Registered Users Only' areas simply register and login.
Parts for polishing who do i use
Moderators: KeithZ1R, chrisu, paul doran, Taffus
:
-
Plumba 54
-
paul doran
- Area Rep.
- Posts: 15910
- Joined: 24th Sep 2004
- Location: near Dublin Ireland
-
limegreen585
- Posts: 11
- Joined: 9th Jan 2007
- Location: NSW Australia
Gentlemen,
I used to get all my alloy etc. polished and paid for it ....... but since Tuesday this week I now do my own, and after a couple of practice runs on some random alloy bike bits in the shed I am now getting the same (very close) results in finish and don't pay apart from initial purchase of the items required (see below)
How ? bought a cheap angle grinder (AU$25.00), 2 x 100mm (4") wool buffing wheels (AU$22.00 for both) and two blocks of polishing compound for AU$12.00 , one was general purpose compound, the other fine for a high quality finish.
After initial prep with various grades of wet and dry paper, I did an old clutch cover with the general compound first, wiped off the waxy residue and then went to work with the finer finishing compound, after about 5 minutes the mirror finish was starting to shine through, I then wiped off the residue and did a final soft cloth polish with Mother's polishing cream.
I reckon with a bit more practice it can only get better. If the cheap angle grinder dies before the 12 month guarantee is up, I will get it replaced for free !!!!
Just a thought for you Gents.
Cheers
BTW I wiped off the residue with a soft rags and mineral turps.
I used to get all my alloy etc. polished and paid for it ....... but since Tuesday this week I now do my own, and after a couple of practice runs on some random alloy bike bits in the shed I am now getting the same (very close) results in finish and don't pay apart from initial purchase of the items required (see below)
How ? bought a cheap angle grinder (AU$25.00), 2 x 100mm (4") wool buffing wheels (AU$22.00 for both) and two blocks of polishing compound for AU$12.00 , one was general purpose compound, the other fine for a high quality finish.
After initial prep with various grades of wet and dry paper, I did an old clutch cover with the general compound first, wiped off the waxy residue and then went to work with the finer finishing compound, after about 5 minutes the mirror finish was starting to shine through, I then wiped off the residue and did a final soft cloth polish with Mother's polishing cream.
I reckon with a bit more practice it can only get better. If the cheap angle grinder dies before the 12 month guarantee is up, I will get it replaced for free !!!!
Just a thought for you Gents.
Cheers
BTW I wiped off the residue with a soft rags and mineral turps.
Last edited by limegreen585 on Thu Jan 11, 2007 11:56 am, edited 1 time in total.
-
limegreen585
- Posts: 11
- Joined: 9th Jan 2007
- Location: NSW Australia
polishers
For those of you in the Birmingham / West midlands area you could try Hayden Finishing in Digbeth, Birmingham 0121 772 5064. He does a cracking job and knows bikes well so he's not likely to polish your bits away to nothing. Usually a fairly quick turnaround and he won't rip you off. I've been using the guy for 20 years never had a problem.
Who is online
Users browsing this forum: No registered users and 14 guests