Is it possible to strip speedo/rev counter to clean condensation stains from the inside of the glass
Thanks
Paul
Hello Guest User,
Please feel free to have a look around the forum but be aware that as an unregistered guest you can't see all of it and you can't post.
To access these 'Registered Users Only' areas simply register and login.
Please feel free to have a look around the forum but be aware that as an unregistered guest you can't see all of it and you can't post.
To access these 'Registered Users Only' areas simply register and login.
z1000 clocks
Moderators: KeithZ1R, chrisu, paul doran, Taffus
-
phil churchett
- Hardcore
- Posts: 3009
- Joined: 28th Mar 2003
- Location: Warwickshire
-
RALPHARAMA
- Area Rep.
- Posts: 3407
- Joined: 19th May 2007
- Location: Pensford, Somerset
- Contact:
It can be done, but you need to be very careful.
I have found that if you use aluminium soft jaws in the vice and gently grip the outer ring that holds the two halves together and carefully open out the 'U' section ring. Open out the bottom section so that it won't show. Use a twisting motion with a good quality screw driver and only work against the section that is being supported by the vice jaws. Patience is the secret. Take it steady and open the whole ring up before attempting the seperate the two halves. Once apart use a glass cleaner to clean the glass. When reassembling open the vice jaws so that they are almost gripping the largest diameter of the top piece. The last one I did I used a bit of silicon on the joint to try and keep the moisure out a bit. Once supported in the vice as above, use a largeish pin punch (around 8-10mm) to dress down the ring. Only dress down against the vice jaws. Initially do both opposite sides of the ring and then move the clock by 90? and dress, then move by 45? etc so that you gradually reform the ring. A little bit at a time is the secret. Just take your time.
It's time consuming but worth it in the end!
I have found that if you use aluminium soft jaws in the vice and gently grip the outer ring that holds the two halves together and carefully open out the 'U' section ring. Open out the bottom section so that it won't show. Use a twisting motion with a good quality screw driver and only work against the section that is being supported by the vice jaws. Patience is the secret. Take it steady and open the whole ring up before attempting the seperate the two halves. Once apart use a glass cleaner to clean the glass. When reassembling open the vice jaws so that they are almost gripping the largest diameter of the top piece. The last one I did I used a bit of silicon on the joint to try and keep the moisure out a bit. Once supported in the vice as above, use a largeish pin punch (around 8-10mm) to dress down the ring. Only dress down against the vice jaws. Initially do both opposite sides of the ring and then move the clock by 90? and dress, then move by 45? etc so that you gradually reform the ring. A little bit at a time is the secret. Just take your time.
It's time consuming but worth it in the end!
Ralph Ferrand
Z1000A1 (1977), Z1300A5 (1983), Z900A4 (1976) GPZ1100 Unitrak (1983)(project), RD250B (1975)(project), ZRX1200R (2005) DT175MX (1981) YZF R6 (1999)
http://www.bikerstoolbox.co.uk
Z1000A1 (1977), Z1300A5 (1983), Z900A4 (1976) GPZ1100 Unitrak (1983)(project), RD250B (1975)(project), ZRX1200R (2005) DT175MX (1981) YZF R6 (1999)
http://www.bikerstoolbox.co.uk
Who is online
Users browsing this forum: No registered users and 15 guests