I'm not too sure ill be liked around here............

zed1015 · #61 PostAuthor: **zed1015** » Sun Dec 09, 2012 11:13 pm

Standard kwak pick-ups.

kiwi kdx · #62 PostAuthor: **kiwi kdx** » Mon Dec 10, 2012 12:35 am

oh... i thought they were all originaly points.

zed1015 · #63 PostAuthor: **zed1015** » Mon Dec 10, 2012 12:53 am

Early kicker engines were points.
Later kickers went to pick-ups around 79/80 with the mk2 etc then all the later j/gpz non kickstarts were all electronic.

kiwi kdx · #64 PostAuthor: **kiwi kdx** » Mon Dec 10, 2012 1:30 am

ah good to know!
are they a good system or still worth putting a Dyna 2000 in there?

big green bus · #65 PostAuthor: **big green bus** » Mon Dec 10, 2012 8:16 pm

they work just fine as long as you have the ignitor. If you want to change it I would fit a Dyna S and green 3ohm coils (you don't need the ignitor with the Dyna S system)

kiwi kdx · #66 PostAuthor: **kiwi kdx** » Thu Dec 27, 2012 8:48 am

I have been looking at CBR1000RR exhausts for a while now and finally took a punt on one for 30 bucks, I don't think it's even beeoa running bike!
You would think it was made to go under the tail of a GPZ1100.

I want it to sit back 2-3inches and up about 1 inch and of corse I'll open it up and take most of the guts out.

Pigford · #67 PostAuthor: **Pigford** » Thu Dec 27, 2012 3:48 pm

That does look like it was made for it :wink:

Rich · #68 PostAuthor: **Rich** » Thu Dec 27, 2012 9:11 pm

How much does it weigh?

kiwi kdx · #69 PostAuthor: **kiwi kdx** » Thu Dec 27, 2012 9:47 pm

its not that heavy at all, at a guess i would say maybe 1-1.5 kg,
but with loosing the original forks, swingarm and rear shocks , its lost a huge amount of weight too.
im not terriably worried about weight, shes gonna be a cruiz'r!

kiwi kdx · #70 PostAuthor: **kiwi kdx** » Thu Dec 27, 2012 10:08 pm

there will be a heap of room left for the mono and electrics, as i will be running the exhaust down the side of the frame to meet up with the cutout in the R1 swinger.

Rich · #71 PostAuthor: **Rich** » Fri Dec 28, 2012 5:28 pm

check the rear wheel movement before putting too much work into the mountings.

kiwi kdx · #72 PostAuthor: **kiwi kdx** » Wed Jan 02, 2013 4:04 am

yeah will do mate, the exhaust will probablly be one of the last bits i do i think.

kiwi kdx · #73 PostAuthor: **kiwi kdx** » Thu Jan 17, 2013 11:13 pm

hey guys, not much to report on the project at the moment other that picking up my new engine cases this weekend.

while sufring the net for parts i have come up with a few bargins...

got this off a 04 R6 with rear caliper hanger and axle for a awesome $40 bucks!

and these for $20 bucks!

so yep... im looking to the next project, even though this one is no where near done.

Pigford · #74 PostAuthor: **Pigford** » Fri Jan 18, 2013 8:53 am

Are the bar risers FAT BAR size :?:

kiwi kdx · #75 PostAuthor: **kiwi kdx** » Sun Jan 20, 2013 9:39 pm

yep sure are.

I'm not too sure ill be liked around here............

Who is online