Hello Guest User,

Please feel free to have a look around the forum but be aware that as an unregistered guest you can't see all of it and you can't post.

To access these 'Registered Users Only' areas simply register and login.

Carburation

Need help restoring, building, or finding then try here.

Moderators: KeithZ1R, chrisu, paul doran, Taffus

Post Reply
Message
Author
User avatar
Surfdeneige
Custard Cream
Custard Cream
Posts: 694
Joined: 8th May 2005
Location: Banchory (Centre of the Universe)

Carburation

#1 PostAuthor: Surfdeneige » Fri May 11, 2007 9:45 am

I have a z1000A2 that runs like a pig. On stripping the carbs I find that they are full of shite. Put them all back together and it runs badly. Can anyone write an idiots guide to carb setup please as my two manuals are pretty vague.

Thanks
A ken fit like!
Top
FLC
Regular Poster
Posts: 53
Joined: 31st Jan 2007

#2 PostAuthor: FLC » Fri May 11, 2007 12:50 pm

First thing to do is balance em using adjustment between carbs.
An old trick i was shown was to hold a piece of tube to your ear and the other end in the carb mouth (with engine running) even a slight difference is very noticable, get them all sounding same,
see how she runs then.
Top
Rich
Hardcore
Hardcore
Posts: 2835
Joined: 4th Mar 2003

#3 PostAuthor: Rich » Fri May 11, 2007 5:01 pm

Clean the shit out of the carbs before you put them back together :D

On a more serious note - adjust cam chain, check valve clearance, check ignition and then start on the carbs. Clean thoroughly not only the fuel jets but the air jets, emulsion tubes and the little holes that supply fuel on tickover as well.

Set fuel hieghts first, set slides by sight - I usually just have a gap visible and then screw the tickover adjuster up. 1 1/4 turns out will be a good starting point for the air / or fuel adjuster screw.
Rich
 diplomacy is a form of art - I was never any good at art
Top
bigguy

Re: Carburation

#4 PostAuthor: bigguy » Fri May 11, 2007 7:40 pm

Surfdeneige wrote:I have a z1000A2 that runs like a pig. On stripping the carbs I find that they are full of shite. Put them all back together and it runs badly. Can anyone write an idiots guide to carb setup please as my two manuals are pretty vague.

Thanks
hiya mate, are you anywhere near south wales? as i have a set of gauge's to balance carb's an would gladly do um for you, normly only take's about 15 - 20 minute's :wink:
Top
User avatar
uk kev
Hardcore
Hardcore
Posts: 1531
Joined: 13th Aug 2006
Location: Berkshire

#5 PostAuthor: uk kev » Sat May 12, 2007 6:34 am

I would also like to know the standard opening setting for the pilot screws please as I have a set of carbs to build, and all the pilot screws were different.
Top
Rich
Hardcore
Hardcore
Posts: 2835
Joined: 4th Mar 2003

#6 PostAuthor: Rich » Sat May 12, 2007 1:02 pm

uk kev wrote:I would also like to know the standard opening setting for the pilot screws please as I have a set of carbs to build, and all the pilot screws were different.


What type of carb? fuel adjuster screw (underneath at the front) or air adjuster screw (top side rear) ?
Rich
 diplomacy is a form of art - I was never any good at art
Top
User avatar
Pigford
Hardcore
Hardcore
Posts: 13314
Joined: 2nd Jan 2006
Location: North Dorset

#7 PostAuthor: Pigford » Sat May 12, 2007 4:52 pm

If screw underneath at front, this controls extra fuel addition at low revs, so wind out about 1/2 turn from fully in, out further richens it.
Screw top side, this is an air screw and works by letting more air (not fuel) into idle system, between 1 1/4 & 1 1/2 turns out. Further out weakens mixture :!:
Sorry for stealing ur glory Rich :blah
And on the 7th day... Zeds were created!
Top
Post Reply

Return to “Bike Help”

Who is online

Users browsing this forum: No registered users and 16 guests