Hello Guest User,

Please feel free to have a look around the forum but be aware that as an unregistered guest you can't see all of it and you can't post.

To access these 'Registered Users Only' areas simply register and login.

Bottom guide roller

Need help restoring, building, or finding then try here.

Moderators: KeithZ1R, chrisu, paul doran, Taffus

Post Reply
Message
Author
z1000Chris
Regular Poster
Posts: 28
Joined: 20th Jul 2007
Location: Watford,England

Bottom guide roller

#1 PostAuthor: z1000Chris » Wed Mar 11, 2009 4:29 am

The new bottom cam chain chain guide roller between the crankcase and block on my z1000a1 is smaller diameter than the one taken out ( only by 5 mm ), does this matter ? Has anyone come across it before ? Help appreciated z1000chris :)
Top
User avatar
Pigford
Hardcore
Hardcore
Posts: 13314
Joined: 2nd Jan 2006
Location: North Dorset

#2 PostAuthor: Pigford » Wed Mar 11, 2009 3:09 pm

If different diameter it will effect the cam timing - slightly :|
And on the 7th day... Zeds were created!
Top
Rich
Hardcore
Hardcore
Posts: 2835
Joined: 4th Mar 2003

#3 PostAuthor: Rich » Wed Mar 11, 2009 7:43 pm

I assume you mean the one at the base of the barrels and not the ones at the cylinder head joint.

It seems to be there mainly to dampen the camchain movement when the chain is going onto the crank. Who did you buy it off - ie are you sure it's for a Z1000 and from a reputable manufacturer ie PMC and not a cam chain tensioner rubber someone is passing on!.
Rich
 diplomacy is a form of art - I was never any good at art
Top
z1000Chris
Regular Poster
Posts: 28
Joined: 20th Jul 2007
Location: Watford,England

#4 PostAuthor: z1000Chris » Wed Mar 11, 2009 11:02 pm

Rich wrote:I assume you mean the one at the base of the barrels and not the ones at the cylinder head joint.

It seems to be there mainly to dampen the camchain movement when the chain is going onto the crank. Who did you buy it off - ie are you sure it's for a Z1000 and from a reputable manufacturer ie PMC and not a cam chain tensioner rubber someone is passing on!.
Yes, its the one at the base of the barrels, a reliable source has told me that the one that was in there was from a z650 which is bigger, so at some stage it had the wrong fitted, can anyone else confirm that a z650 one is bigger than one from a z1000 many thanks
Top
HowieD
100Club
100Club
Posts: 336
Joined: 5th Feb 2008
Location: Lincoln

#5 PostAuthor: HowieD » Wed Mar 11, 2009 11:30 pm

Doesn't a Z650 have a HI-Vo Chain not a morse chain as Z1000's do?

if in doubt buy the correct one is my advice.
CD185, Maggot, Z1-R, Horace
Top
Steve Cooke
Hardcore
Hardcore
Posts: 1612
Joined: 18th Mar 2007
Location: Southampton

#6 PostAuthor: Steve Cooke » Thu Mar 12, 2009 6:44 am

The Z1000 one measures 48mm outside diameter, this is measured on a used one so it is only approximate but should be close enough to decide which one is correct.
Top
z1000Chris
Regular Poster
Posts: 28
Joined: 20th Jul 2007
Location: Watford,England

roller

#7 PostAuthor: z1000Chris » Thu Mar 12, 2009 7:52 am

Steven Cooke wrote:The Z1000 one measures 48mm outside diameter, this is measured on a used one so it is only approximate but should be close enough to decide which one is correct.
Many thanks, I've been supplied the right one then :)
Top
Pasc
Hardcore
Hardcore
Posts: 1656
Joined: 4th Jun 2006
Location: W Mids

#8 PostAuthor: Pasc » Thu Mar 12, 2009 10:03 pm

HowieD wrote:Doesn't a Z650 have a HI-Vo Chain not a morse chain as Z1000's do?

if in doubt buy the correct one is my advice.

Howie, the early ones had morse but then went to HiVo on the later models.
Top
Post Reply

Return to “Bike Help”

Who is online

Users browsing this forum: Google [Bot] and 15 guests