Page 1 of 1
new paid up member with z1000 a2 project
Posted: Sun Jan 27, 2013 10:47 am
Author: Spen72
hi guys...been on here for a year now,and just paid up...
said hi to a few of you and been a pain in the arse just as much...sorry Ginger Bear....so i thought it was time to put a few photo's for one of my project's on here...its a z1000 1978 a2,done a bit to it allready like change to headlight from a custom twin to the one you see here...it has a harris pipe and d.i.d rim's fitted and a deep brace swing arm...the engine is an z1a motor...hope you like and the photo's work...
it has z900 bages on at mow...but i willl fit some z1000 one's when i find some..
will put more photo's on as work is done to her..
Posted: Sun Jan 27, 2013 11:28 am
Author: 000zeds
Looks like a 16 inch rear wheel off an LTD you have on the back,
Z-Power should have Z1000 badges.
Posted: Sun Jan 27, 2013 11:34 am
Author: zmaxmotorsports
I like that headlight,whats it off of?
Posted: Sun Jan 27, 2013 11:49 am
Author: Ginger Bear
Sweet looking Zed there Spence, rear caliper & torque arm don't look to be 1000A2.
Here's a link for your badges, I had a pair for me toast rack project & must say the quality is good.
https://www.z-power.co.uk/merchantmanag ... cts_id=203
new paid up member with z1000 a2 project
Posted: Sun Jan 27, 2013 12:03 pm
Author: Spen72
The wheels are d.i.d rim's from japan...yes 16" but not ltd..and got the headlight off an old z650..thanks Ginger Bear about the badges, will look them up..not sure what the rear caliper is as was with the bike when I got it...but it fits ok...
Posted: Sun Jan 27, 2013 12:04 pm
Author: Pigford
That looks really nice lad .........
Soopa-Doopa 
Posted: Sun Jan 27, 2013 12:07 pm
Author: Mark Tiller
new paid up member with a z1000 a2 project
Posted: Sun Jan 27, 2013 12:47 pm
Author: Spen72
here's a pic of the rear d.i.d wheel...if anyone can tell me what the caliper is????
and the idy tail that i got from hobbo...
thanks for all your advice to guys about the badges...
next on the list is to rebuild thr front master cylinder...
Posted: Sun Jan 27, 2013 1:01 pm
Author: Mark Tiller
You might want to considder this instead of the repair option
https://www.z-power.co.uk/merchantmanag ... cts_id=819
Posted: Sun Jan 27, 2013 1:03 pm
Author: Mark Tiller
GPZ caliper?
Posted: Sun Jan 27, 2013 1:44 pm
Author: Mr Puffin
Yes that certainly looks like a GPZ/J series calipern
Posted: Sun Jan 27, 2013 1:51 pm
Author: z1bman
CALLIPER Z1000 J / Z1100 ST GPZ 1100 B1/B2
Posted: Sun Jan 27, 2013 2:07 pm
Author: 000zeds
Is that front mudguard fibreglass
If so may need a brace as the standard + shorty ones have a double skin across top between mounting points
new paid up member with z1000 a2 project
Posted: Sun Jan 27, 2013 2:13 pm
Author: Spen72
Thanks pigford for the comment about my zed...and about the rear caliper guy's. .that helps me out...as for the front mudguard its a metal one twozeds..
new paid up member with z1000 a2 project
Posted: Sun Jan 27, 2013 2:22 pm
Author: Spen72
Ps in between the pic's... that should be tidy tail from hobbo...bloody spell check. ..
