Page 1 of 1
Fitting electronic ignition
Posted: Thu Jan 01, 2009 4:22 pm
Author: Richardz900
The HT lead has broken where it enters the coil on my z900 A4, i'v now decided to fit a Boyer Bransden Micro-Power CDI which includes new coils which i'll be ordering from z-power. Has anyone got any advice as to how to fit this myself? Or should it be taken to a garage to be done? I have basic knowledge and don't want to start the job if I cant finish it. Any tips will be appreciated.
Cheers
Posted: Thu Jan 01, 2009 4:56 pm
Author: wilsonsjw11
Richard.
Just fitted a Dyna S system and 3 ohm coils to my Z1B,easy to follow instructions,can't go wrong,just make sure you fit some heat shrink tubing to the mounting bolts/spacers so LT side does not short to earth,pm me if you need some heat shrink tubing
Best Regards
Steve
Re: Fitting electronic ignition
Posted: Thu Jan 01, 2009 4:59 pm
Author: Pigford
Richardz900 wrote:The HT lead has broken where it enters the coil on my z900 A4, i'v now decided to fit a Boyer Bransden Micro-Power CDI which includes new coils which i'll be ordering from z-power. Has anyone got any advice as to how to fit this myself? Or should it be taken to a garage to be done? I have basic knowledge and don't want to start the job if I cant finish it. Any tips will be appreciated.
Cheers
The general consensus on here is go DYNA everytime....
I got a new DYNA S ignition for grabs....
Boyer Branstonpickle systems don't seem to be too robust...
Posted: Thu Jan 01, 2009 5:01 pm
Author: FER
Do not buy the Boyer system . Dyna everytime .
fer
Posted: Thu Jan 01, 2009 5:02 pm
Author: wilsonsjw11
Mark
Can I be your marketing/promotions manager
Regards
Steve
Happy new year!!!!
Posted: Thu Jan 01, 2009 5:03 pm
Author: Pigford
wilsonsjw11 wrote:Mark
Can I be your marketing/promotions manager
Regards
Steve
Happy new year!!!!
Whats you % cut
Posted: Thu Jan 01, 2009 5:03 pm
Author: london calling
Piggy,I thought you had a Brand New Combine Harvester
Posted: Thu Jan 01, 2009 5:05 pm
Author: Pigford
london calling wrote:Piggy,I thought you had a Brand New Combine Harvester
Jack-M-Lad..... But I
won't give you the key
Posted: Thu Jan 01, 2009 5:08 pm
Author: london calling
Touche
Posted: Thu Jan 01, 2009 5:31 pm
Author: Rich
If you can set points up it should be no problem for you to put elec ignition on. You will need a strobe and a basic idea of wiring would be an advantage.
Posted: Thu Jan 01, 2009 5:36 pm
Author: Pigford
Intial set up, don't even need a strobe..... Manually hold on 'full advance' & check marks.... won't be too far out
Posted: Thu Jan 01, 2009 6:25 pm
Author: Richardz900
hi pigford, is the dyna s compleat with coils, if not what coils would i need. what u want for it. thanks for advice, regards & happy new year . richard.
Posted: Thu Jan 01, 2009 6:30 pm
Author: Pigford
Richard....... sorry but I've been pm'd by a member who's just bought it off me......
But Dyna S can be used with standard coils no probs... or Dyna Coils... 2.2 or 3.0 ohms
Posted: Thu Jan 01, 2009 6:36 pm
Author: Richardz900
wilsonsjw11 wrote:Richard.
Just fitted a Dyna S system and 3 ohm coils to my Z1B,easy to follow instructions,can't go wrong,just make sure you fit some heat shrink tubing to the mounting bolts/spacers so LT side does not short to earth,pm me if you need some heat shrink tubing
Best Regards
Steve
thanks for advice steve. got some tubing but thanks, will fit it myself
regards & happy new year richard
Posted: Thu Jan 01, 2009 7:00 pm
Author: Richardz900
thanks to all for advice,
dyna s its got to be. happy new year to all, richard.