z650 single sided or mono shock info wanted please

Koreanbaz · #1 PostAuthor: **Koreanbaz** » Sat Sep 08, 2012 5:35 pm

I've been searching but don't seem to be getting far, but there must be some.

I'm looking for a picture of a Z650 with either a single sided swing arm or a mono shock.

questions being,

Which swing arm?

Crofty · #2 PostAuthor: **Crofty** » Sat Sep 08, 2012 7:51 pm

http://forums.kz650.info/index.php?topic=2232.0

http://www.oldskoolperformance.com/foru ... &start=154

2 minutes googling found these, there will be loads on other sites

Koreanbaz · #3 PostAuthor: **Koreanbaz** » Sun Sep 09, 2012 6:54 am

Crofty wrote:http://forums.kz650.info/index.php?topic=2232.0

http://www.oldskoolperformance.com/foru ... &start=154

2 minutes googling found these, there will be loads on other sites

you did well young Luke.

However the first link won't let me in as not a member and the second is of a Z1

I have also found similar whilst Googling and surfing. but Z650 seem more illusive , but thank you and I'll join the first link sight in search of my quest

Koreanbaz · #4 PostAuthor: **Koreanbaz** » Sun Sep 09, 2012 7:13 am

Crofty wrote:http://forums.kz650.info/index.php?topic=2232.0

http://www.oldskoolperformance.com/foru ... &start=154

2 minutes googling found these, there will be loads on other sites

tried to join KZ forum but apparently I'm SPAM, yet I don't even like the stuff! :roll:

HARRY4448 · #5 PostAuthor: **HARRY4448** » Sun Sep 09, 2012 7:29 am

Click the KZ Info logo at the top of the page and it'll let you into the forum

#6 PostAuthor: **Ginger Bear** » Sun Sep 09, 2012 8:11 am

I've moved this to 'Bike help'.

But it would be useful to know how wide your original swinger is at the 'pivot point'.

750steve · #7 PostAuthor: **750steve** » Sun Sep 09, 2012 4:43 pm

Koreanbaz wrote:
Crofty wrote:http://forums.kz650.info/index.php?topic=2232.0

http://www.oldskoolperformance.com/foru ... &start=154

2 minutes googling found these, there will be loads on other sites

tried to join KZ forum but apparently I'm SPAM, yet I don't even like the stuff!

fook me, if they let ME in they'll let you in!!

CAT3 · #8 PostAuthor: **CAT3** » Tue Sep 11, 2012 1:04 pm

Forget it Baz, there's no room on the ramp :lol:

Crofty · #9 PostAuthor: **Crofty** » Tue Sep 11, 2012 3:05 pm

However the first link won't let me in as not a member and the second is of a Z1

Second is actually a Z650 frame with an 1100 engine in, it does not have the mount on the lower frame rail under the engine.

GPZ750 unitrac arm might fit, you need to get a tape measure out and go check a few arms, at the end of the day there will be lots that fit, just depends how much work you want to do.

oldzed · #10 PostAuthor: **oldzed** » Sun Sep 23, 2012 9:35 am

I had a z650 b model with a complete gpz600r rear end.

fitted into the frame fine.It was however a 16" rear wheel .The bearings were just a mix of 650 and 600r parts

In fairness I also had a gpz750 unitrack engine ,not an 1100 but I only had to have the cush drive machined to run the chain straight