Z1OwnersClub GB

The brake splitter on my A4 is mounted to the lower yoke by a pair of 45mm long bolts that also hold the cable eyes. There is a spacer on each bolt that holds the splitter away from the yoke. One of mine is missing and I cannot find a part number for it in the parts book. The spacer is 10mm O/D and 12mm long

Is this a bodge ( the bike has had a front end prang at some point and not been well repaired) or should they be there?

If so, has anybody got one I can buy, beg etc,etc

Or do I mount the splitter so that it abuts the face of the lower yoke and use shorter bolts?

1 43015-032 CYLINDER ASSY,MASTER Not Available
2 43073-001 REPAIR SET-MASTER CYL $42.57
3 43025-001 STOPPER-BOOTS Not Available
4 43024-001 BOOTS Not Available
5 481J1800 CIRCLIP,18MM $2.97
6 43022-001 STOPPER-PISTON Not Available
7 43072-001 PISTON ASSY Not Available
8 43019-001 CUP-PRIMARY Not Available
9 43018-001 SPRING ASSY-RETURN Not Available
10 43017-001 VALVE ASSY-CHECK Not Available
11 43029-003 LEVER,FRONT BRAKE $41.75
12 43033-004 BOLT Not Available
13 312AA0600 NUT-HEX $2.97
14 43031-001 WASHER-LOCK,8MM Not Available
15 317AA0800 NUT-HEX-SMALL,8MM $2.97
16 43030-003 BOLT,LEVER ADJUSTING Not Available
17 43026-1054 CAP-BRAKE Not Available
18 43027-001 PLATE-MASTER CYLINDER $5.04
19 43028-001 DIAPHRAGM $16.83
20 112N0625 BOLT-UPSET $2.97
21 411AA0600 WASHER-PLAIN,6.5X13X1 $2.97
22 43034-001 HOLDER-MASTER CYL Not Available
23 49091-0001 WASHER-SEAL,10.1X14.5X1.5 $2.97
24 92153-0627 BOLT,OIL,L=23 $2.97
25 49006-1041 BOOT,DUST $5.23
26 43059-022 HOSE,FRONT BRAKE Not Available
27 43065-001 SWITCH-FRONT BRAKE Not Available
28 43061-002 JOINT,THREE WAY Not Available
29 110N0636 BOLT HEX HEAD 6X36 Not Available
30 110N0645 BOLT,HEX HEAD,6X45 Not Available
31 461DA0600 WASHER-SPRING,6MM $2.97
32 411AA0600 WASHER-PLAIN,6.5X13X1 $2.97
33 43059-011 HOSE,FRONT BRAKE Not Available
34 43060-021 PIPE,BRIDGE Not Available
35 43063-001 BRACKET-BRAKE HOSE Not Available
36 43064-001 GROMMET-HOSE BRACKET Not Available
37 92027-162 COLLAR,6.8X10X12 $3.53
38 11012-1037 CAP,FRONT BRK SWITCH Not Available

bill. the two collars are only fitted to the single disc brake splitter. if you have the twin disc splitter you do not need the collars. although i cannot see what purpose they serve

Are they not for the headlamp support bracket ?

No headlamp support bracket on an A4 due to the indicator warning buzzer

Thanks everybody,

It did not occur to me that the single disc set up would be different to the double disc - and it was the double disc page that I was open when rebuilding the front end.

The thread has achieved two things - first it confirms that the A4 does have these spacers and second and really pleasingly I have had a pm and one is on its way to me....

Another example of the spirit and comradery in this club.