Suddenly my headlight is not working.
Bulb is fine.
I don't get 12 v at the two wires, both low and high beam.
Position light (the small one) is fine.
Any suggestions?
What should I check?
Thanks

At the end I found a very good mechanic.
6 valves was bent.
Work has been done properly.
Carbs have been cleaned as well.
Now bike is smooth like silk.

chrisu wrote:if you've bent the valve then it'll need to be replaced - head off job i'm afraid.

no real alternative.

Do you believe that such clearance increase means valve bent? We are talking about 0.30 clearance increase.
Which are the risk to fire the bike and test compression?
Thanks

With 305 I should have 0.1 clearance. Am I right?

Ciao

Thanks for your valuable suggestions. Yesterday I managed to install properly (I believe) the cam shafts. I have checked the clearance and I am afraid that one valve has bent. I am talking about intake valve cylinder 4. Before it was clearance zero with 280 shim. I put 270 and now clearance is 0.45....

hi, I removed both cam shaft because I was not able to take 2 shims even with the special tool. Today I have assemble everything following this instruction: http://i1180.photobucket.com/albums/x404/alinus65/Mobile%20Uploads/IMG_1884_zps64057687.jpg http://i1180.photobucket.com/albums/x404/alinus65/M...

Sump removed, strainer cleaned.
Everything works well. No light even at idle.
Thanks

Dont!!!!!! run this bike till you have sorted out problem potential for big problems.. understand....I believe I have to remove the sump and check the strainer However by changing the switch the situation has improved a lot. As said the light is on only with hot engine at 1000 rpm. Above 1000 rpm i...

I am having same problem. With hot engine the light was on below 3000 rpm. I have replaced the oil pressure switch. Now light is off with cold engine. It turns on with hot engine (after 15 minutes) but only at idle rmp. Above 1500 rpm is off. My oil is Motul 5100 10w40. Since I am using this bike on...

Thanks
I am checking cables.
Otherwise I'll contact Al during winter time.
Ciao

Hi, The needle of my speedometer is fluctuation a lot above 80 kmh. The needle of my rev counter is fine up to 4000. After that is not moving smoothly. I understood it is a common problem. As far as I know the instruments are originals. I have no experience. What should I check by myself without mak...

here attached images of my bike. today was the first ride after the mechanic made the tuning of the carbs. few problems: - oil pressure light is on when rpm is below 2000. I have removed the oil pressure switch for cleaning but problem is not solved. According to the mechanic nothing wrong with the ...

Just to show my beast.... :D Which bike is it? http://i1180.photobucket.com/albums/x404/alinus65/macchia%20nera/Photo31-08-12210631_zpsc48b936d.jpg http://i1180.photobucket.com/albums/x404/alinus65/macchia%20nera/Photo31-08-12210622_zps1bfc4809.jpg http://i1180.photobucket.com/albums/x404/alinus65/m...

jimmock wrote:Or.......


Just sell it to me for 100 Euros as a non runner !!

I'll deal with the transport myself.


GORGEOUS LOOKING BIKE!!!!

I am paying for the shipping door to door. Give me your address

If the green was disconnected you may find the other wire to the other pair of coils disconnected. Check the two wires and make sure you have connected the green to and black wires to the right set of coils. as per z1bmans comments .the left hand coil is for spark plugs no 1+4 + has 1 black+ 1 yell...